EVALUATION OF LOCALLY SOURCED BARITE, CALCITE AND HAEMATITE AS WEIGHTING MATERIALS IN NEEM OIL-BASED DRILLING FLUID
Keywords:
Neem oil;, oil-based drilling fluid, weighting materials, barite, calcite, haematite, rheologyAbstract
To increase the mud density and increase drilling-fluid density, this study focuses on assessing various locally materials employed in oil-based drilling fluid formulation. Neem oil is used as a replacement for diesel in oil-based drilling fluid. The physicochemical properties of the oil analysed were the specific gravity, flash point, viscosity, pour point and pH. The values obtained are 0.9228, 172 0C, 3.6 0C and 6.1 respectively. The FTIR analysis indicates cm-1 and esters. Wyoming grade bentonite and Sabon Gari Ngalda bentonite were used in the formulation of the oil based drilling fluids. Barite, Calcite and Haematite were added at varying weight concentrations (0%, 5%, 10%, 15%, 20% and 25%) to increase the mud density. Varying oil-based drilling fluid samples designated A, B, C, D, E and F were analyzed for mud weight, plastic viscosity, yield point, , gel strength, filtration volume at 5 minutes interval, mud thickness and pH. Significant changes in Mud weight, Plastic Viscosity, Yield Point, Apparent Viscosity, Gel strength were noted to correspond to changes in the concentration of mud with variation of the weighing agents (Barite, Calcite and Haematite). The filtrate water volume increases at an interval of 5 minutes while the thickness of the cake of Haematite mud formulation has a close value of 7.97mm and 7.56mm respectively than the formulation made with Calcite and Haematite. The pH of Calcite mud formulation has the highest values of 9.1 and 8.8 than the formulation made with Barite and Haematite. Addition of locally sourced weighting materials from Nigeria (Barite, Calcite and Haematite) increased the density of the drilling fluid under the tested conditions. Thus, all the weighting materials can be used as weighing agents in drilling mud formulation.
References
Abdou, M. I., Al-Sabagh, A. M., Ahmed, H. E. S., & Fadl, A. M. (2018). Impact of barite and ilmenite mixture on enhancing the drilling mud weight. Egyptian Journal of Petroleum, 27(4), 955–967. https://doi.org/10.1016/j.ejpe.2018.02.004
Adachi, J., Bailey, L., Houwen, O. H., Meeten, G. H., Way, P. W., Growcock, F. B., & Schlemmer, R. P. (2004). Depleted zone drilling: Reducing mud losses into fractures. In SPE/IADC Drilling Conference. https://doi.org/10.2523/87224-MS
Adewale, F. J., Lucky, A. P., Oluwabunmi, A. P., & Boluwaji, E. F. (2017). Selecting the most appropriate model for rheological characterization of synthetic-based drilling mud. International Journal of Applied Engineering Research, 12(18), 7614–7629.
Agwu, O. E., Okon, A. N., & Udoh, F. D. (2015). A comparative study of diesel oil and soybean oil as oil-based drilling mud. Journal of Petroleum Engineering, 2015, Article 828451. https://doi.org/10.1155/2015/828451
Ahmed, A. W., & Kalkan, E. (2019). Drilling fluids: Types, formation choice and environmental impact. International Journal of Latest Technology in Engineering, Management & Applied Science, 8(12), 66–71.
Anawe, P. A., Etim, U. J., Udo, M. E., & Umoren, S. A. (2018). Evaluation of the rheological properties of clay-based drilling fluids modified with xanthan gum and carboxymethylcellulose (CMC). Journal of Petroleum Science and Engineering, 162, 222–228. https://doi.org/10.1016/j.petrol.2017.12.003
Apugo-Nwosu, T. (2011). Studies on the suitability of Ubakala bentonitic clay for oil well drilling mud formulation. British Journal of Applied Science & Technology, 1(4), 152–171. https://doi.org/10.9734/bjast/2011/407
Arora, R. (2015). Introduction to MATLAB®. In Optimization (pp. 309–320). CRC Press. https://doi.org/10.1201/b18469-14
Ayonmike, C., & Okeke, I. (2015). Effect of temperature on the rheological properties of water-based drilling fluids. International Journal of Scientific and Engineering Research, 387–391.
Barette, G. (2011). Drilling mud: Chemistry and technology. Editions Technip.
Bilal, S., Adamu, M. S., & Mohammed-Dabo, I. A. (2021). Effect of temperature on oil-based drilling fluid formulated from castor seed oil and locally sourced Nigerian Tongo bentonite. Journal of Materials and Environmental Science, 12(1), 55–65.
Bourgoyne, A. T., Jr., & Chenevert, M. E. (1986). Applied drilling engineering. Society of Petroleum Engineers.
Chikwe, A. O., Onuh, C. H., Ajugwe, U. J., & Nwagbo, C. A. (2019). Development of environmentally friendly oil-based mud using almond oil, castor oil and groundnut oil. American Journal of Engineering Research, 12, 88–98.
Darley, H. C. H., & Gray, G. R. (1988). Composition and properties of drilling and completion fluids (5th ed.). Gulf Publishing Company.
Delikesheva, D. N., Syzdykov, A. K., Ismailova, J. A., Kabdushev, A. A., & Bukayeva, G. A. (2020). Measurement of the plastic viscosity and yield point of drilling fluids. *13*(1), 58–65.
Fadairo, A., Falode, O., Ako, C., Adeyemi, A., & Ameloko, A. (2012). Novel formulation of environmentally friendly oil-based drilling mud. In New technologies in the oil and gas industry. https://doi.org/10.5772/51236
Falode, O. A., Alawode, A., Ehinola, O. A., & Boore, D. A. (2020). Investigation of local weighting materials as a substitute to barite in drilling mud formulation. Journal of Materials & Metallurgical Engineering, 10(1), 39–48.
Ichenwo, J. L., & Ogbonna, J. (2018). Effect of weighing agent on rheological properties of drilling fluid. International Journal of Engineering Research & Technology, 7(4). https://doi.org/10.17577/IJERTV7IS040322
Julius, U., Offiong, I., & Idorenyin, O. (2015). The use of galena as weighting material in drilling mud. Journal of Scientific Research and Reports, 7(6), 455–465. https://doi.org/10.9734/jsrr/2015/15095
Mahmudur Rahman, K. (2018). Analysis of drilling fluid rheology & pressure drop modelling to improve drilling efficiency [Master's thesis, University of Calgary].
Mohamed, A., Basfar, S., Elkatatny, S., & Al-Majed, A. (2019). Prevention of barite sag in oil-based drilling fluids using a mixture of barite and ilmenite as weighting material. Sustainability, 11(20), Article 5617. https://doi.org/10.3390/su11205617
Ogbeide, P. O., & Igbinere, S. A. (2016). The effect of additives on rheological properties of drilling fluid in highly deviated wells. FUTO Journal Series, 2(2), 68–82.
Olatunde, A. O. (2012). Improvement of rheological properties of drilling fluid using locally based materials. Petroleum & Coal, 54(1), 65–75.
Olatunde, A. O., & Usman, A. M. (2011). Comparative analysis of rheological properties of water-based drilling fluids formulated from local and imported clay. Journal of Petroleum Science and Engineering, 77(1), 80–85.
Omole, O., Adeleye, J. O., Falode, O., Malomo, S., & Oyedeji, O. A. (2013). Investigation into the rheological and filtration properties of drilling mud formulated with clays from northern Nigeria. Journal of Petroleum and Gas Engineering, 4(1), 1–13. https://doi.org/10.5897/JPGE09.017
Onojake, M. C., & Chikwe, T. N. (2019). Rheological properties of some oil-based muds used in reservoirs in the Niger Delta, Nigeria. Global Journal of Pure and Applied Sciences, 25, 39–44. https://doi.org/10.4314/gjpas.v25i1.6
Paul, A. A. L., & Adewale, F. J. (2018). Novel synthetic-based drilling fluid through enzymatic interesterification of canola oil. https://doi.org/10.1155/2018/6418090
Preveen, K. R. (2012). Study on castor oil as oil-based fluid in drilling.
Saied Bahrainian, S., Nabati, A., & Hajidavalloo, E. (2018). Improved rheological model of oil-based drilling fluid for south-western Iranian oilfields. Journal of Petroleum Science and Technology, 8(3), 53–71. https://doi.org/10.22078/jpst.2017.2706.1459
Shah, S. N., Shanker, N. H., & Ogugbue, C. C. (2010). Future challenges of drilling fluids and their rheological measurements. In American Association of Drilling Engineers Fluids Conference and Exhibition (Vol. 10, pp. 1–16).
Downloads
Published
Issue
Section
License
Copyright (c) 2026 This is an Open Access article distributed under the terms of the Creative Commons Attribution 4.0 International License, which permits unrestricted use, distribution, adaptation, and reproduction in any medium, provided that the original work is properly cited.

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
Authors are permitted to post their work online in institutional/disciplinary repositories or on their own websites. Pre-print versions posted online should include a citation and link to the final published version in Journal of Librarianship and Scholarly Communication as soon as the issue is available; post-print versions (including the final publisher's PDF) should include a citation and link to the journal's website.